A new version of the firmware for the Kung Fu Flash Cartridge by Kim Jørgensen is released.

Changelog from version v1.21 to 1.34:

• Fix broken mount D64 file option (since v1.33)
• Improve disk drive emulation to support Sidplay64. Thanks Actarus, Fabuseta, mwedmark, and Seni1ix
• Support basic SD2IEC commands.
• Optimized code to make it all fit in flash.
  • In this version the following cartridge types will not require the firmware file on the SD card:
  • Normal cartridge (8k, 16k, Ultimax)
  • Fun Play, Power Play
  • Super Games
  • Ocean type 1
  • Epyx Fastload
  • C64 Game System, System 3
  • Dinamic
  • Zaxxon, Super Zaxxon
  • Magic Desk, Domark, HES Australia
  • EasyFlash
  • Prophet64
  • RGCD, Hucky
  • Drean
  • C128 Normal Cartridge (external function ROM)
• Combined PAL and NTSC firmware.
• T64 support (normal tape files only). Thanks Matthias.
  • The firmware has been extended to support both PAL and NTSC and this requires the KungFuFlash_v1.30.upd file to be kept in the root directory of the SD card.
  • Older firmware will not support this extended format so KungFuFlash_v1.30_upgrade.upd must be used first. This file is not needed after the upgrade process has been completed.
• Fix broken EasyFlash VIC-II/C128 mode. Thanks mrr19121970.
• Improve detection of C64 clock signal.
• Add simple diagnostic tool.
  • The diagnostic tool is started by pressing the menu button for 2 seconds (until the LED turns off) and is intended to help debug stability problems on some C64 models.
  • The tool can also be started in a USB only mode if Kung Fu Flash refuses to start at all. In this mode debug data is send via USB only and the C64 should start normally (boot to Basic). This mode is started by pressing both the special and menu button for 2 seconds, then releasing the menu button followed by the special button.
  • For reference the phi2 clock frequency should be around 985248 Hz for PAL and around 1022727 Hz for NTSC.
• Add support for Drean cartridges. Thanks beatmaster13.
• Add support for C128 normal cartridge. Thanks phako.
• Fix unstable EF3 USB. Thanks dikdom.
• Add support for Super Games cartridge.
• Add support for Prophet64 cartridge.
• Fix broken Fun Play/Power Play cartridge support (since v1.16)
• Add support for RGCD and Hucky cartridges. Thanks Konstantin19.
• Load extensionless files as PRG.
• Add support for WarpSpeed by SvOlli. Thank you.
• Add support for Freeze Frame/Freeze Machine. Thanks gold11-carca.
• Fix bug reading UPD file using FAT16. Thanks cosmo6128.

Download:

• Kung Fu Flash Firmware v1.34 (729)

source: github.com/KimJorgensen/KungFuFlash

NEW TAG: C64 BIG GAME PACK

Some new games or tools (Cracked / Trained or Unrealeased) for Commodore 64 have been released from your favorites groups.

Titles:

• The Third Planet From Altair (RPL)
• The Last Ninja [1581]
• DX-7 Sounddesign
• Combat Crazy +7H (EasyFlash)
• Rogue Burger One +5F
• Laura64 Preview V2 +2T
• Infernal Runner +1DT
• DX-7 Support
• (Super) Bonkey Kong +2HD
• Demons Castle 2 [english]
• Cow & Chicken Preview (TRIAD/PROTOVISION)
• Combat Crazy +7H
• Limbo Preview
• Hibernated 1: This Place is Death (R17)
• Drugwar 64
• Hibernated 1: This Place is Death (R17) +D
• Zombie Calavera Prologue – Hokuto Force
• Zombie Calavera Prologue – Hardstyle
• Rush Preview +2
• The Scroll of Akbar Khan +1DMW
• Drugwar 64 V1.05
• Terminator 2 +H (EasyFlash)
• Brainway +DCM
• Blastopia
• Ill Savior Preview 2
• CETI 21 – Special Edition +2 [seuck]
• Blastopia +6HD
• Aviator Arcade II Preview V2 +3
• Illsavior Preview 2
• Fizz +1F
• Austro-Comp E1+E2 [german]
• Aviator Arcade II Preview [sd2iec]
• Bomberland 64k [sd2iec]
• Spider Maze +3D
• Spider Maze
• Highnoon +6DGMH
• GameTro +
• Get Off My Garden! +5H
• LumberJack Basic
• Four in a Row Master +T
• Caverns of Khafka +10D
• Street Gang +7DH

Download: All Games in One Archive (6908)

source: csdb.dk

NEW TAG: C64 BIG GAME PACK

Some new games or tools (Cracked / Trained or Unrealeased) for Commodore 64 have been released from your favorites groups.

Titles:

• Cabal +8DFHIR
• Tetris MP [2in1] +F
• Retaliate Preview 2 +2
• Retaliate Preview 2 +
• Retaliate V0.2 Beta
• Lemmings +15DF [easyflash]
• UFF +2TPDF [english]
• Number King
• Ratekoenig
• Axe of Rage +10DMHF
• Retaliate V0.2.1 Beta (Hotfix)
• Find The Pussy
• Jake the Snake V2.2
• Retaliate Preview 2 +3H
• Snake 360 Preview +
• Snake 360 Preview
• Painter +4DH
• Kevin in the Woods Preview +
• Steel Ranger Preview +C
• Balloon Flight +HF
• Wizard
• Trainsmission +1
• Trainsmission +
• Crazy Cars III +6D [easyflash]
• Tink Tonk Castle Clobber +
• Killed Until Dead +D [easyflash]
• Steel Ranger +3C Trainer
• Retaliate Preview 3 +3
• Fallout Hacker
• H.E.R.O. II Preview 2
• Fallout Hacker +1D
• Pirates! [german] [1581]
• Iceblox Plus +5HF
• Killed Until Dead +D [easyflash]
• Where in Time is Carmen Sandiego [easyflash]
• Battle Command [sd2iec]
• Metro Blitz +3DH
• Zork (53 Columns)
• Alien 3 [easyflash]
• Gindevmbly
• Border Blast 3 Enhanced +2H [seuck]
• Dark Destroyer 2117 RX +2 [seuck]
• Delta Run RX +2DH [seuck]
• Valentine’s Day Shopping Simulator +
• Navy Moves +7DFHIRW
• Indeflataball +7HF
• Vitamin +4CTD
• Bounder (Competition Edition)
• Zork III (Proportional Font)

Download: All Games in One Archive (5729)

source: csdb.dk

This is a program that can playback .SID files found in the HVSC collection on a real Commodore 64/128.

Make sure you have the most recent HVSC version for your sid files. It was designed for both PAL and NTSC computers, and will play all sid songs at correct system speed.

Versions of the program:

• sidplay64-normal.prg – Standard version for 1541, 1571, 1581 and clones.
• sidplay64-sd2iec.prg – SD2IEC version.
• sidplay64-reu-1541u2cmd.prg – 1541 Ultimate II version with REU.
• sidplay64-reu-sd2iec.prg – SD2IEC version with REU.
• sidplay64-reu-1541u-netdrive.prg – 1541 Ultimate & Netdrive with REU.
• sidplay64-reu-iec-cmd-ide64.prg  – CMD drives, IDE64 devices & other IEC devices, with REU.
• sidplay64-sidfx-reu-normal.prg – Sidfx and REU version for 1541, 1571, 1581 and clones of these.

(Again : The 1541U2 software iec mode has been disabled for this build.)

SIDPLAY 64 v1.21 (15/01/2018):

• Updated SIDFX card detection.

SIDPLAY 64 v1.20 (29/09/2017):

• Added SIDFX card support. Software control for switching beween 6581 or 8580.
• Sidplay64 detects the sidfx card. The sid chips. And will then ask you to center Switch 1 to allow for software control of the sid chips.
• Added Chameleon support for two emulated sid chips.
• Software control for switching between 6581 or 8580.
• Sidplay64 will switch to correct sid type when you load sids.

Download: SIDPlay 64 v1.21 (1250)

source: sourceforge.net

This is a program that can playback .SID files found in the HVSC collection on a real Commodore 64/128.

You will find different versions of SP64 in this package, most of themwill work on all devices. But I suggest you use the correct version for for your device, since they might contain special commands.

Versions of the program:

• sidplay64-reu-1541u2cmd.prg – 1541 Ultimate II version with REU.
• sidplay64-reu-sd2iec.prg – SD2IEC version with REU.
• sidplay64-reu-1541u-netdrive.prg – 1541 Ultimate & Netdrive with REU.
• sidplay64-reu-iec-cmd-ide64.prg – CMD drives, IDE64 devices & other IEC devices, with REU.
• sidplay64-reu-normal.prg – REU version for 1541, 1571, 1581 and clones of these.
• sidplay64-1541u2cmd – 1541 Ultimate II version.
• sidplay64-normal.prg – Standard version for 1541, 1571, 1581 and clones.
• sidplay64-1541u-netdrive.prg – 1541 Ultimate & Netdrive.
• sidplay64-iec-cmd-ide64.prg- CMD drives, IDE64 devices & other IEC devices.
• sidplay64-sd2iec.prg – SD2IEC.

(The 1541U2 software iec mode has been disabled for this build.)

Changelog SIDPLAY 64 v1.10 (17/04/2016):

• Added: IEC/CMD/IDE64: ClrHome key loads more filenames while reading directory.
• Added: IEC/CMD/IDE64: Joystick RIGHT loads more filenames while reading directory.
• Behaviour: BASIC sid’s that stops on its own can be exited by pressing CBM.
• Added: Songs with BASIC start support.
• Added: REU: Remembers previous dir positions when you go back.
• Added: REU: File size are displayed in kilobytes. (Not for 1541u2)
• Behaviour: Restore : resets variables and reloads dir.
• Behaviour: RunStop+Restore : exit BASIC sid’s or sid’s using $0000 as play call.
• Fixed: 1541U2: shortened dir read routine.
• Fixed: One of the color skins used dark grey for border.

Download: SIDPlay 64 (SP64) v1.10 (1121)

source: sourceforge.net

This is a program that can playback .SID files found in the HVSC collection on a real Commodore 64/128.

You will find different versions of SP64 in this package, most of themwill work on all devices.  But I suggest you use the correct version for for your device, since they might contain special commands.

Versions of the program:

• sidplay64-reu-1541u2cmd.prg – 1541 Ultimate II version with REU.
• sidplay64-reu-sd2iec.prg – SD2IEC version with REU.
• sidplay64-reu-1541u-netdrive.prg – 1541 Ultimate & Netdrive with REU.
• sidplay64-reu-iec-cmd-ide64.prg – CMD drives, IDE64 devices & other IEC devices, with REU.
• sidplay64-reu-normal.prg – REU version for 1541, 1571, 1581 and clones of these.
• sidplay64-normal.prg – Standard version for 1541, 1571, 1581 and clones.
• sidplay64-1541u-netdrive.prg – 1541 Ultimate & Netdrive.
• sidplay64-iec-cmd-ide64.prg- CMD drives, IDE64 devices & other IEC devices.
• sidplay64-sd2iec.prg – SD2IEC.

(The 1541U2 software iec mode has been disabled for this build.)

Download: SIDPlay 64 (SP64) v1.0.0 (1108)

source: sourceforge.net

Hi all, like one year ago Manosoft amazes us again, this time he did a great job of merging the ITS TAP Player module with the C64SD and from this merger comes the Princess, an interface with both previously released interfaces.
The Princess interface is elegant as only Manosoft can do, the box color has changed and is a white sand that matches perfectly with the whole 8-bit Commodore Home Computer series.

In addition to the color were also added new controls and visual led. Below the instructions of each command on the front/back side of the Princess interface.

Front side:

• [1] Play/Stop switch for TAP file.
• [2] Reset button.
• [3] Disc Change button. (down/autoswap.lst)
• [4] LED:
  • Yellow – Virtual Motor of the Tape.
  • White – Reading.
  • Red – General Error.
  • Green – Power.
• [5] Floppy Drive Connector (IEC) Computer side.
• [6] Connector Cassette side Computer
• [7] Auxiliary Power 9v.

Back side:

• [1] SD Card slot.
• [2] Red Button – Setpoint tap file / (up/autoswap.lst)
• [3] Dip Switch for selecting the Floppy drive Device (SD2IEC).
• [4] Audio volume (monitor function) TAP Player.
• [5] Mini DIN 8-pin connector to be connected to the tape port of the Commodore 264 series.
• [6] Auxiliary Power 9v.
• [7] Pass-through Floppy Drive Connector (IEC)
• [8] Pass-through Tape connector to use with a Datasette 1530 or 1531 with a another adapter.

Like the previous C64SD v2.0 interface, the Princess has a pass-through connector for the cassette recorder and one for the Floppy Disk Drive.

I don’t forget to speak about the nice addition, a small Piezo Speaker to hear the sound of the bytes that are loaded with the TAP Player and also a nice “beep” that warn if the interface on power up working correctly.

Damiano alias “Manosoft” is a good manufacturer of 8 Bit peripherals and also a great friend. I take the opportunity of this article to greet Damiano and congratulate for this new interface for the 8-bit Commodore Home Computer series.

Soon will be available on the Manosoft website two new software packages (C64 and AIO)

“AIO” is an innovative system that will allow the creation of the SD Card of 4GB or higher in a few minutes from an image file created ad hoc.

On the Commodore 64 side was also written a new program called “MENU” with some utilities like the initialization of the SD Card for the Princess C64SD v3.0 interface.

The development of the TAP Player firmware with the SD2IEC protocol has been made possible thanks to the collaboration of Hawui1 promoter and developer of the ITS Module and some other things.

The Princess C64SD v3.0 interface will be available for sale in the next months on the Manosoft site.

Princess C64SD v3.0 Video Preview:

A new version of the firmware for the interface C64SD Infinity + ITS Module by Manosoft is released.

Changelog:

• Implemented functionality that allows to save a placeholder (unique for each .TAP file) pressing the red button on the back of the card. User can set back the read pointer at which TAP data is played back by pressing “Next” button on the card. Useful for multi load .TAP or games asking to reset the counter of the tape and then to rewind the tape that specific point.

Download: C64SD (ITS) Firmware v0.10.3.9 (1534)

source: manosoft.it

This program works as a program launcher for Commodore machines. Even if it was originally intended for a device with sd2iec firmware, it works also with any CBM drive (without sd2iec functions of course).

It is a multi-system version derived from the discontinued sd2brwse v.0.6 by Hannu Nuotio (fork() of sdbrowse v.0.7)

The Vic-20 Mega-Cart Installer is based on sys.asm sources of mega-tools by Daniel Kahlin, sort routine by Michael Kircher.

Current supported machines:

• C64.
• C64DTV.
• Vic-20 unexpanded.
• Vic-20 +3K RAM.
• Vic-20 +8K RAM or plus (for FE3 use this version)
• Vic-20 with Mega-Cart.
• C16 / C116 / Plus4.
• C128 in 64 mode.
• C128 80 Columns.

Tested drives:

• MMC2IEC
• SD2IEC
• uIEC
• C64-SD (any version, with ITS modules too)
• 1541 (with JiffyDOS too)
• 1541-II
• 1571
• 1581

Changelog:

• v.0.1 – 01-Sep-2009 (Start of project, C64/C64DTV only)
• v.0.2 – 21-Oct-2009 (First working version for Vic-20 +8K RAM)
• v.0.3 – 06-Jan-2010 (Added memory config auto-detection for Vic-20 selected program)
• v.0.4 – 19-Jan-2010 (Added support for Vic-20 with Mega-Cart and manual start mode)
• v.0.5 – 10-Feb-2010 (Added support for Vic-20 unexpanded and Vic-20 +3K RAM)
• v.1.0 – 05-Mar-2010 (First public version, minor issues fixed, C64 and Vic-20 supported)
• v.1.1 – 22-Jun-2010 (Added support for D41 and DNP file images, sd2iec firmware v.0.9.0 or higher required)
• v.1.2 – 09-Oct-2010 (Added SJLOAD speed-up option to the manual mode of the Mega-cart version)
• v.1.3 – 31-May-2012 (Added support for C16/C116/Plus4, Sort directories, cosmetic changes)
• v.1.4 – 19-Jul-2012 (Added JIFFYDTV speed-up support for C64-DTV, Clear screen before RUN)
• v.1.5 – 03-Mar-2013 (Added support for C128, and uppercases disk images D64,D81,D71 etc.)
• v.1.6 – 20-Aug-2013 (Added support for Tap files using ITS modules, case insensitive disk images Dnp, TaP, m2I etc.)

Download: CBM FileBrowser v1.6 (3617)

source: vic20.it/cbmfilebrowser

A new version of the firmware for the interface C64SD Infinity + ITS Module by Manosoft is released.

Changelog:

• Added support for the long filenames and the ones containing special characters.

Download: C64SD Firmware v0.10.3.8 (1451)

source: manosoft.it

It was released a new firmware for the C64SD Infinity + ITS Module by Manosoft which fixes some minor compatibility issues present in the previous release with some C64 Filebrowser.

Download: C64SD Firmware v0.10.3.7 (1375)

source: manosoft.it

Autopsy:

I have to thank my friend Damiano for sending me the ITS Module with a low serial number, which like the previous one (C64SD v2.0) i really appreciate it.

The ITS module is a interface that enables SD2IEC to play .TAP files version 1 and version 2 to a commodore machine. The ITS module was designed to fit into the pass-through tape connector of C64SD Infinity and to be connected to the C64SD by a four wires cable that allows C64SD to manage it.

SD2IEC firmware has been modified in order to add the commands and the routines needed to control the external ITS module without removing any of the original SD2IEC functionalities

Features:

• Play back any V1 or V2 standard .TAP files in order to load them into a commodore machine belonging to the “classic” or “264” series including: VIC-20, VC20, C64, C16, C116, C128 (all
• versions) and Plus/4. Note: some models of C128D doesn’t have the tape edge-card connector, of  course ITS is not compatible with these machines.
• Rebuild the original tape grabbed into all the .TAP version 1 and for most of the version 2
• Work permanently connected between the tape port of the commodore computers and the corresponding datassette (either 1530 white model flat plug or 1531 black model mini-din plug) acting
• As a pass-through transparent gateway or activated in order to play back .TAP files: no need to connect and disconnect the module to use your datassette.
• Play back .TAP content with optimal accuracy and completely in digital format without the hassle of file conversions or level adjustment
• Simulate tape motor activation logic fully so that the play back of the tape is managed as it would be in a real C2N tape. An override button has been provided able to stop the play back of the “virtual tape” at any time when necessary.
• Work with either 1530 (White model, flat plug) datassette recorder as well as with 1531 (Black, mini-din plug) datassette
• Load .TAP with multiple programs recorded one after the other (like the classic tape compilations sold in the 80′s)  

What Can’t You Do:

• Create a .TAP file representing the content of a Tape (i.e. ITS is not a “tape content grabber”)
• Fix the content of a TAP file in case it’s broken. Broken .TAP won’t load on your Commodore box. Since there are literally thousands of utilities to create and manipulate .TAP files there is the possibility to come across non-standard or incorrect .TAP files.
• Play back the content of .TAP of version V0. Use an utility to convert V0 .TAP files to V1 such as TapClean then you will be able to use the converted .TAP file with ITS module.
• Manage programs saved on tape that are based on the tape-counter management or on the time of wind-rewind of the tape.

The ITS Module can be purchased on the Manosoft site.

ITS Tape Loading video:

source: manosoft.it

This program works as a program launcher for Commodore machines. Even if it was originally intended for a device with sd2iec firmware, it works also with any CBM drive (without sd2iec functions of course).

It is a multi-system version derived from the discontinued sd2brwse v.0.6 by Hannu Nuotio (fork() of sdbrowse v.0.7)

The Vic-20 Mega-Cart Installer is based on sys.asm sources of mega-tools by Daniel Kahlin, sort routine by Michael Kircher.

Current supported machines:

• C64.
• C64DTV.
• Vic-20 unexpanded.
• Vic-20 +3K RAM.
• Vic-20 +8K RAM or plus (for FE3 use this version)
• Vic-20 with Mega-Cart.
• C16 / C116 / Plus4.
• C128 in 64 mode.
• C128 80 Columns.

Changelog:

• v.0.1 – 01-Sep-2009 (Start of project, C64/C64DTV only)
• v.0.2 – 21-Oct-2009 (First working version for Vic-20 +8K RAM)
• v.0.3 – 06-Jan-2010 (Added memory config auto-detection for Vic-20 selected program)
• v.0.4 – 19-Jan-2010 (Added support for Vic-20 with Mega-Cart and manual start mode)
• v.0.5 – 10-Feb-2010 (Added support for Vic-20 unexpanded and Vic-20 +3K RAM)
• v.1.0 – 05-Mar-2010 (First public version, minor issues fixed, C64 and Vic-20 supported)
• v.1.1 – 22-Jun-2010 (Added support for D41 and DNP file images, sd2iec firmware v.0.9.0 or higher required)
• v.1.2 – 09-Oct-2010 (Added SJLOAD speed-up option to the manual mode of the Mega-cart version)
• v.1.3 – 31-May-2012 (Added support for C16/C116/Plus4, Sort directories, cosmetic changes)
• v.1.4 – 19-Jul-2012 (Added JIFFYDTV speed-up support for C64-DTV, Clear screen before RUN)
• v.1.5 – 03-Mar-2013 (Added support for C128, and uppercases disk images D64,D81,D71 etc.)

Download: CBM FileBrowser v1.5 (3773)

source: vic20.it/cbmfilebrowser

Commodore Free Magazine Issue #64

Free to download Commodore magazine dedicated to Commodore Computers.

Download:

• Commodore Free Magazine Issue #64 (D64) (1081)
• Commodore Free Magazine Issue #64 (PDF) (1177)
• Commodore Free Magazine Issue #64 (TXT) (1414)

source: commodorefree.com

This program works as a program launcher for Commodore machines. Even if it was originally intended for a device with sd2iec firmware, it works also with any CBM drive (without sd2iec functions of course).

It is a multi-system version derived from the discontinued sd2brwse v.0.6 by Hannu Nuotio (fork() of sdbrowse v.0.7)

The Vic-20 Mega-Cart Installer is based on sys.asm sources of mega-tools by Daniel Kahlin, sort routine by Michael Kircher.

Current supported machines:

• C64.
• C64DTV.
• Vic-20 unexpanded.
• Vic-20 +3K RAM.
• Vic-20 +8K RAM or plus (for FE3 use this version)
• Vic-20 with Mega-Cart.
• C16 / C116 / Plus4.
• C128 in 64 mode.

Changelog:

• v.0.1 – 01-Sep-2009 (Start of project, C64/C64DTV only)
• v.0.2 – 21-Oct-2009 (First working version for Vic-20 +8K RAM)
• v.0.3 – 06-Jan-2010 (Added memory config auto-detection for Vic-20 selected program)
• v.0.4 – 19-Jan-2010 (Added support for Vic-20 with Mega-Cart and manual start mode)
• v.0.5 – 10-Feb-2010 (Added support for Vic-20 unexpanded and Vic-20 +3K RAM)
• v.1.0 – 05-Mar-2010 (First public version, minor issues fixed, C64 and Vic-20 supported)
• v.1.1 – 22-Jun-2010 (Added support for D41 and DNP file images, sd2iec firmware v.0.9.0 or higher required)
• v.1.2 – 09-Oct-2010 (Added SJLOAD speed-up option to the manual mode of the Mega-cart version)
• v.1.3 – 31-May-2012 (Added support for C16/C116/Plus4, Sort directories, cosmetic changes)
• v.1.4 – 19-Jul-2012 (Added JIFFYDTV speed-up support for C64-DTV, Clear screen before RUN)

Download: CBM FileBrowser v1.4 (1409)

source: vic20.it/cbmfilebrowser