Some new games or tools (Cracked / Trained or Unrealeased) for Commodore 64 have been released from your favorites groups.

Titles:

• Elidon +7DM
• Conway’s Game Of Life
• Harrier Strike +3
• Locomotive Preview
• Deep Star +4
• Codename Desert Storm +3
• Liberator Preview
• Mission Moon +2J 101%
• Megapede +DG
• Gigamaze +ED
• 911 Tiger Shark +2 [ntsc]
• Agent-X II +1DG
• Submarine Rescue +5
• Submarine Rescue
• Mission Moon
• Sheep vs. Fox DX +2H
• Job Race +2D
• Press It!
• Angry Birds Style
• Murray Mouse +26D
• Quod Init Exit v1.4
• Flin Flon
• Assembloids (Retail Version) +2HD

Download: All Games in One Archive (2661)

source: csdb.dk

These two computers had the classic fault: Black screen of Death.

The first one was repaired by replacing a ram chip (4264) partially interrupted, the other one had One of the two chip PLA dead.

I have to thank my friend Andrea for providing me a motherboard of a 8296 for spare parts, where i have recovered the PLA which i needed.

Autopsy:

12►

from Wikipedia:

The Commodore 8050 and Commodore 8250 were dual unit 5¼” floppy disk drives for Commodore International computers. They used a wide rectangular steel case form similar to that of the Commodore 4040, and used the IEEE-488 interface common to Commodore PET/CBM computers.

The 8050 was a single sided drive, whereas the 8250 could use both sides of a disk simultaneously. Both used a “quad” density format storing approximately 0.5 megabyte per side. The density of media was similar to later PC high density floppy disks, but the 8050 and 8250 could not use PC high density disks reliably. Since “quad” density disks were rare even at the time, users quickly found that typical double density floppy disks had enough magnetic media density to work in these drives.

These drives were not dual mode, so they could not read or write disks formatted by the more common lower capacity Commodore 1541 or Commodore 4040 models.

Some variants of these drives existed. The Commodore 8250LP was the 8250 in a lower profile, tan-colored case. The Commodore SFD-1001 was a single drive version of the 8250 in a Commodore 1541 style case (similarly to the Commodore 2031LP), often used by bulletin board systems for their physical similarity to 1541s and high capacity and speed.

Photo of the repair:

The 8250LP Floppy Drive is arrived with the following faults:

• The main motor of the Floppy Drive D0 spins only for a couple of seconds and then stops.
• The Floppy Drive D1 have a problem of the hinge for the disk pressure.

About the problem of the motor of Drive D0 have been replaced a voltage regulator 7812 and an electrolytic capacitor in losses. The mechanics of the Drive D1 was repaired using the Loctite.

source: wikipedia

Sorry, this entry is only available in Italian.

CBM prg Studio Version 2.8.0 is released. There are a lot of new features in this version. I’d really appreciate it if you report any bugs you find or have any suggestions/comments.

CBM prg Studio allows you to type a BASIC or Machine Code program in using a nice Windows environment and convert it to a ‘.prg’ file which you can run on an emulator, or even a real C64 / VIC20 or PET if you’re feeling brave and have the right kit.

CBM prg Studio is the result of merging C64PrgGen and VIC20PrgGen. Adding new features and fixing bugs in two apps which were 95% similar was a bit of a nightmare so merging them made sense.

It was also a good opportunity for a face lift and to add some new features, such as:

• Programs are project based, meaning all related source files, sprite files etc. are kept in one place and multiple source files can be linked more easily.
• Tabbed MDI.
• Syntax highlighting.

What CBM prg Studio isn’t is a front-end for tok64, cbmcnvrt, bastext or any other tokeniser / detokeniser / assembler. It’s all been written completely from scratch.

New features:

• Screen RAM viewer for debugger.
• Ignore/truncate REM statements during code generation switch.
• Project comments.
• The character editor’s scratch pad can be imported to the screen editor.
• Save/load configuration settings.
• Import multicolour bitmaps into the sprite editor.
• Export binary files from the character editor.
• Much improved BASIC and assembly generation time.

See the help for a complete list of bug fixed.

Download: CBM prg Studio v2.8.0 (991)

source: ajordison.co.uk

Autopsy:

Here you can see a hack of my dtv (Direct-to-TV).

from Wikipedia:

The C64 Direct-to-TV, called C64DTV for short, is a single-chip implementation of the Commodore 64 computer, contained in a joystick (modeled after the mid 1980s Competition Pro joystick) with 30 built-in games. The design is similar to the Atari Classics 10-in-1 TV Game. The circuitry of the C64DTV was designed by Jeri Ellsworth, a self-taught computer chip designer who had formerly designed the C-One.

Tulip Computers (which had acquired the Commodore brand name in 1997) licensed the rights to Ironstone Partners, which cooperated with DC Studios, Mammoth Toys, and “The Toy:Lobster Company” in the development and marketing of the unit.[1] QVC purchased the entire first production run of 250,000 units and sold 70,000 of them the first day they were offered.

There exist multiple versions of the C64DTV. DTV1 (NTSC television type) comes with 2 MB ROM. It first appeared in late 2004 for the American/Canadian market. DTV2 (called C64D2TV sometimes) is a revised version for the European and world markets (PAL television type) and appeared in late 2005. The ROM has been replaced by flash memory in these devices. However, the DTV2/PAL version suffers from a manufacturing fault, which results in poor colour rendering (the resistors in the R-2R ladder DACs for both the chroma and the luma have been transposed). In the DTV3, a problem with the blitter was fixed. Another DTV variant is the Radio Shack “HUMMER Off-Road Racing Challenge Video Game”.

Hardware Specifications:

Core circuity:

• ASIC running at 32 MHz internally, implementing 6510 CPU, VIC-II, SID, CIA, and PLA

Casing/Connectors:

• Integrated in a Joystick (as if connected to port 2 of a real C64)
• Five additional buttons (acting like keys)
• Running from batteries only (four AA batteries)
• Composite Video, monaural audio (RCA connectors)
• Looks similar to a Competition Pro joystick

Graphics:

• NTSC (DTV2 and later: NTSC/PAL on chip, only PAL wired in end-market devices)
• Reprogrammable palette with 4 bits of luma and 4 bits of chroma
• DTV2 and later: “chunky” 256 color mode, additional blitter for fast image transformation

Sound:

• No support for SID filters
• DTV2 and later: 8 bit digital sound, additional options for envelope generators

Memory:   

• DTV1: 128 KB RAM, 2 MB ROM
• DTV2 and later: 2 MB RAM, 2 MB flash memory
• DMA engine for RAM/RAM and ROM/RAM transfers
• DTV2 and later: additional RAM access using bank switching and blitter

CPU:

• Implementing a 6510 at 1 MHz
• DTV2 and later: Enhanced CPU (fast/burst mode, additional registers and opcodes, support for illegal ops of the 6510)

source: wikipedia dtvhacking.retrosafe.com

Autopsy:

The Expandamem of CompuThink (Compu/Think) is a Memory expansion card for Commodore PET (chicklet keyboard) and KIM-1.

The memory expansion was installed inside the Computer Commodore PET and with a particular hook was fixed above the motherboard. The connection was through the expansion bus and a power connector.

Download: CompuThink Memory Expansion Manual (1650)

Autopsy:

from Zimmers homepage:

The Commodore 1600 was an extremely prolific and inexpensive modem, introducing millions of computer users to the online world. Marketed to the VIC-20 user, the “VICMODEM” as it was nicnamed, operated in an extremely strange manner.

Instead of connecting to the phone line directly, the VICMODEM relied on a connection THROUGH the phone to the handset. One would dial the number they wished to connect to, then remove the extension from their handset, plugging it into the modem after a carrier signal is heard.

Some customers in Canada were lucky enough to get their VICMODEM packaged with this telephone manufactured in Canada by Northern Telecom. Ironically, the phone did not have a detachable handset, making it useless by itself for use with the modem. Therefore, the set also included a small adaptor which allowed one to plug the VICMODEM directly into the wall line cable, daisy chained to the phone. After dialing with the phone, a switch on the adaptor would redirect the carrier signal to the modem.

Download: Commodore VIC Modem Model 1600 Manual (1709)

source: zimmers.net

Autopsy:

123►

from Wikipedia:

The Amstrad CPC (short for Colour Personal Computer) is a series of 8-bit home computers produced by Amstrad between 1984 and 1990. It was designed to compete in the mid-1980s home computer market dominated by the Commodore 64 and the Sinclair ZX Spectrum, where it successfully established itself primarily in the United Kingdom, France, Spain, and the German-speaking parts of Europe.

The series spawned a total of six distinct models: The CPC464, CPC664, and CPC6128 were highly successful competitors in the European home computer market. The later plus models, 464plus and 6128plus, efforts to prolong the system’s lifecycle with hardware updates, were considerably less successful, as was the attempt to repackage the plus hardware into a game console as the GX4000.

The CPC models’ hardware is based on the Zilog Z80A CPU, complemented with either 64 or 128 kB of memory. Their computer-in-a-keyboard design prominently features an integrated storage device, either a compact cassette deck or 3″ floppy disk drive. The main units were only sold bundled with a colour or monochrome monitor that doubles as the main unit’s power supply. Additionally, a wide range of first and third party hardware extensions such as external disk drives, printers, and memory extensions, was available.

The CPC series was pitched against other home computers primarily used to play video games and enjoyed a strong supply of game software. The comparatively low price for a complete computer system with dedicated monitor, its high resolution monochrome text and graphic capabilities and the possibility to run CP/M software also rendered the system attractive for business users, which was reflected by a wide selection of application software.

During its lifetime, the CPC series sold approximately three million units.

Cleaning / Replacement of the little rubber, reconstruction of pitches with a soft pencil:

source: wikipedia cpcwiki.eu

Autopsy:

123►

from Wikipedia:

The Amstrad CPC (short for Colour Personal Computer) is a series of 8-bit home computers produced by Amstrad between 1984 and 1990. It was designed to compete in the mid-1980s home computer market dominated by the Commodore 64 and the Sinclair ZX Spectrum, where it successfully established itself primarily in the United Kingdom, France, Spain, and the German-speaking parts of Europe.

The series spawned a total of six distinct models: The CPC464, CPC664, and CPC6128 were highly successful competitors in the European home computer market. The later plus models, 464plus and 6128plus, efforts to prolong the system’s lifecycle with hardware updates, were considerably less successful, as was the attempt to repackage the plus hardware into a game console as the GX4000.

The CPC models’ hardware is based on the Zilog Z80A CPU, complemented with either 64 or 128 kB of memory. Their computer-in-a-keyboard design prominently features an integrated storage device, either a compact cassette deck or 3″ floppy disk drive. The main units were only sold bundled with a colour or monochrome monitor that doubles as the main unit’s power supply. Additionally, a wide range of first and third party hardware extensions such as external disk drives, printers, and memory extensions, was available.

The CPC series was pitched against other home computers primarily used to play video games and enjoyed a strong supply of game software. The comparatively low price for a complete computer system with dedicated monitor, its high resolution monochrome text and graphic capabilities and the possibility to run CP/M software also rendered the system attractive for business users, which was reflected by a wide selection of application software.

During its lifetime, the CPC series sold approximately three million units.

Replacement/Adaptation of a power switch for Amstrad CPC 464:

source: wikipedia cpcwiki.eu

I have decided to replace my Amiga 1000 keyboard (US version) with the space key yellowed and a hole in the plastic caused by a wrong installation with a Amiga 1000 keyboard (Italian version) cosmetically perfect and running.

I bought a few things from the site Retro Innovations of Jim Brain.

6540 Rom Adapter:

• This PCB converts the MOS 6540 DIP pinout to a JEDEC standard 2764-27512 EPROM pinout.  The optional 5 upper address lines are available via pads complete with provision for pullup resistors (10K).

Commodore IEC Disk Drive Cable:

• This very short cable is useful for my second Ultimate 1541.

This program works as a program launcher for Commodore machines. Even if it was originally intended for a device with sd2iec firmware, it works also with any CBM drive (without sd2iec functions of course).

It is a multi-system version derived from the discontinued sd2brwse v.0.6 by Hannu Nuotio (fork() of sdbrowse v.0.7)

The Vic-20 Mega-Cart Installer is based on sys.asm sources of mega-tools by Daniel Kahlin, sort routine by Michael Kircher.

Current supported machines:

• C64.
• C64DTV.
• Vic-20 unexpanded.
• Vic-20 +3K RAM.
• Vic-20 +8K RAM or plus (for FE3 use this version)
• Vic-20 with Mega-Cart.
• C16 / C116 / Plus4.
• C128 in 64 mode.
• C128 80 Columns.

Tested drives:

• MMC2IEC
• SD2IEC
• uIEC
• C64-SD (any version, with ITS modules too)
• 1541 (with JiffyDOS too)
• 1541-II
• 1571
• 1581

Changelog:

• v.0.1 – 01-Sep-2009 (Start of project, C64/C64DTV only)
• v.0.2 – 21-Oct-2009 (First working version for Vic-20 +8K RAM)
• v.0.3 – 06-Jan-2010 (Added memory config auto-detection for Vic-20 selected program)
• v.0.4 – 19-Jan-2010 (Added support for Vic-20 with Mega-Cart and manual start mode)
• v.0.5 – 10-Feb-2010 (Added support for Vic-20 unexpanded and Vic-20 +3K RAM)
• v.1.0 – 05-Mar-2010 (First public version, minor issues fixed, C64 and Vic-20 supported)
• v.1.1 – 22-Jun-2010 (Added support for D41 and DNP file images, sd2iec firmware v.0.9.0 or higher required)
• v.1.2 – 09-Oct-2010 (Added SJLOAD speed-up option to the manual mode of the Mega-cart version)
• v.1.3 – 31-May-2012 (Added support for C16/C116/Plus4, Sort directories, cosmetic changes)
• v.1.4 – 19-Jul-2012 (Added JIFFYDTV speed-up support for C64-DTV, Clear screen before RUN)
• v.1.5 – 03-Mar-2013 (Added support for C128, and uppercases disk images D64,D81,D71 etc.)
• v.1.6 – 20-Aug-2013 (Added support for Tap files using ITS modules, case insensitive disk images Dnp, TaP, m2I etc.)

Download: CBM FileBrowser v1.6 (3574)

source: vic20.it/cbmfilebrowser

Some new games or tools (Cracked / Trained or Unrealeased) for Commodore 64 have been released from your favorites groups: Sitzgruppe, TRIAD, Lifeless Incorporated, Prof. Pi^2, Onslaught, Nostalgia, Genesis Project and Laxity.

Download:

• Pimple Panic Preview (1032)
• Defmon &D (1027)
• Motor Massacre / Road Raiders 101% +18DIR (1089)
• Warriors +6 101% (1002)
• Stalingrad Campaign +D and Map (1045)
• The Vice Squad (preview) (1032)
• Bunker Runner (1034)
• Schloss-Geist +4H (1000)
• Hells Bells +H (1009)
• Frospi +4 (1051)
• Cuby +3H (1032)
• The Great Escape +2H (1029)
• Lemmings [unofficial] Preview + (1031)
• The Vice Squad Preview +4 (1017)
• Dictator 101% +h (1044)
• All Games in One Archive (2682)

source: csdb.dk

If you are the lucky owners of these eprom: Motorola MCM 68766C you can do something really cute, hardware permitting. Example: use this EPROM like a ROM for some Devices and Computers Commodore without using an adapter ;-D

I had to use the EPROM programmer Promenade C1 for Commodore 64 to burn these eprom because all my programmers don’t support these type of eprom.

Download:

• Eprom Motorola MCM68766C Datasheet (1848)
• Prom-Shell v2.00 (720)