Autopsy:

123►

I had to build the power cable (8.5 – 10 volts), video Composite output and In/Out tape, because was not given with the computer as standard.

from Wikipedia:

MicroBee (Micro Bee) was a series of home computers by Applied Technology, later known as MicroBee Systems.

The original MicroBee computer was designed in Australia by a team including Owen Hill and Matthew Starr. It was based on features available on the DG-Z80 and DG-640 S-100 cards developed by David Griffiths, TCT-PCG S-100 card developed by TCT Micro Design and MW6545 S-100 card developed by Dr John Wilmshurst. It was originally packaged as a two board unit, with the lower “main board” containing the keyboard, Zilog Z80 microprocessor, Synertek 6545 CRT controller, 2 kB of “screen” RAM, 2 kB of character ROM (128 characters) and 2 kB of Programmable Character Graphics (PCG) RAM (128 characters). Each byte in the screen RAM addressed a character in either the character ROM or PCG RAM. A second board, termed the “core board”, contained the memory, and on later models also included a floppy disk controller.

The computer was conceived as a kit, with assembly instructions included in Your Computer magazine, in June 1982. After a successful bid for the New South Wales Department of Education computer tender, the computer was repackaged in a two-tone beige and black case, and sold pre-built. The 16 kB ROM held the MicroWorld BASIC interpreter written by Matthew Starr and DGOS (David Griffiths Operating System) compatible System Monitor. In addition to the 16 kB ROM, there is additional ROM socket for optional programs such as WORDBEE (Word processor) or EDASM (a Z80 Editor/Assembler that was written by Ron Harris).

Original MicroBees ran at a clock speed of 2 MHz, with a video dot clock of 12 MHz, which was sufficient to display 64 × 16 characters (512 × 256 pixels) on a modified television or composite monitor. The original machines were supplied with 16 or 32 kB of static RAM, and stored programs on cassette, using 1200 Baud encoding.

source: wikipedia

Autopsy:

123►

I have repaired the PSU with the failure of stanby mode of the Sharp X68000 (gray version). The failure was caused by two electrolytic capacitors and the voltage regulator 7805 in short circuit.

I have also tried to repair the external case of the Sharp X68000 (gray version) that during the first transport in Italy many years ago was destroyed.

from Wikipedia:

The Sharp X68000, often referred to as the X68k, is a home computer released only in Japan by the Sharp Corporation. The first model was released in 1987, with a 10 MHz Motorola 68000 CPU (hence the name), 1 MB of RAM and no hard drive; the last model was released in 1993 with a 25 MHz Motorola 68030 CPU, 4 MB of RAM and optional 80 MB SCSI hard drive. RAM in these systems is expandable to 12 MB, though most games and applications did not require more than two.

The X68k ran an operating system developed for Sharp by Hudson Soft, called Human68k, which features commands very similar to those in MS-DOS (typed in English). Pre-2.0 versions of the OS had command line output only for common utilities like “format” and “switch”, while later versions included forms-based versions of these utilities, greatly improving their usability. At least three major versions of the OS were released, with several updates in between. Other operating systems available include NetBSD for X68030 and OS-9.

Early models had a GUI called “VS” (Visual Shell); later ones were packaged with SX-WINDOW. A third GUI called Ko-Windows existed; its interface is similar to Motif. These GUI shells could be booted from floppy disk or the system’s hard drive. Most games also booted and ran from floppy disk; some were hard disk installable and others require hard disk installation.

Since the system’s release, Human68k, console, and SX-Window C compiler suites and BIOS ROMs have been released as public domain and are freely available for download.

Early machines use the rare Shugart Associates System Interface (SASI) for the hard disk interface; later versions adopted the industry-standard small computer system interface (SCSI). Per the hardware’s capability, formatted SASI drives can be 10, 20 or 30 MB in size and can be logically partitioned as well. Floppy disks came in a couple of different formats, none of which are natively readable on other platforms, although software exists that can read and write these disks on a DOS or Windows 98 PC.

source: wikipedia

Autopsy:

123►

I have built a cable from 6-DIN to VGA to use this computer with a Monitor VGA Multisync (15khz)

from Wikipedia:

The X1 is a series of home computer released by Sharp Corporation from 1982 to 1988. It was based on a Z80 CPU.

Despite the fact that the Computer Division of Sharp Corporation had released the MZ series, suddenly the Television Division released a new computer series called the X1. At the time the original X1 was released, all other home computers generally had a BASIC language in ROM. However the X1 did not have a BASIC ROM, and it had to load the Hu-BASIC interpreter from a cassette tape. On the plus side however, this concept meant that a free RAM area was available that was as big as possible when not using BASIC. This policy was originally copied from the Sharp MZ series, and they were called clean computers in Japan. The cabinet shape of X1 was also much more stylish than others at that time and a range of cabinet colors (including Red) was selectable.

The RGB display monitor for the X1 had a television tuner, and a computer screen could be super-imposed on TV. All the TV functions could be controlled from a computer program. The character font was completely programmable (A.K.A. PCG) with 4bit color, and it was effectively used into a lot of games. The entirety of the VRAM memory was mapped on to the I/O area, so it was controlled without bank change. Since X1 had these features, it was very powerful for game software.

While X1 was struggling to sell, the PC8801 (from NEC) was quickly becoming popular in the Japanese market. In 1984, Sharp released the X1 turbo series with high resolution graphics (640×400, while X1 had 640×200). It had a lot of improvements, but the clock speed was still only 4 MHz. In 1986, Sharp released the X1 turbo Z series with a 4096 color analog RGB monitor. An X1 twin, which had a PC-Engine in the cabinet, was finally released as the last machine of the X1 series in 1987. Then this series was succeeded by the X68000 series.

Sharp continues to sell desktop PC/TV combos in Japan through its Internet Aquos line, where an X1-style red color scheme is available.

Download: Sharp X1 (CZ-812CR) Rom (1403)

source: wikipedia

Today a friend, that i thank him immensely, gave me a large amount of chips.

The donation amounts to:

• 70+ Z80 CPU.
• 14+ Z80 CTC (Counter / Timer Channels)
• 200+ 74XXX TTL chips.

I ran the repair of the membrane that had a micro interruption, i have used a micro-drop of vinilic glue mixed with the graphite that i have scraped from the pencil ikea, i made a thin film on the microfracture and now it works.

There were other problems, including: graphite consumed in some keys and the keyboard connector (pcb side) don’t work very well.

Autopsy:

12►

The horrible holes for the switch and the button are used to halt the CPU and RESET.

from Wikipedia:

The Amstrad CPC (short for Colour Personal Computer) is a series of 8-bit home computers produced by Amstrad between 1984 and 1990. It was designed to compete in the mid-1980s home computer market dominated by the Commodore 64 and the Sinclair ZX Spectrum, where it successfully established itself primarily in the United Kingdom, France, Spain, and the German-speaking parts of Europe.

The series spawned a total of six distinct models: The CPC464, CPC664, and CPC6128 were highly successful competitors in the European home computer market. The later plus models, 464plus and 6128plus, efforts to prolong the system’s lifecycle with hardware updates, were considerably less successful, as was the attempt to repackage the plus hardware into a game console as the GX4000.

The CPC models’ hardware is based on the Zilog Z80A CPU, complemented with either 64 or 128 kB of memory. Their computer-in-a-keyboard design prominently features an integrated storage device, either a compact cassette deck or 3″ floppy disk drive. The main units were only sold bundled with a colour or monochrome monitor that doubles as the main unit’s power supply. Additionally, a wide range of first and third party hardware extensions such as external disk drives, printers, and memory extensions, was available.

The CPC series was pitched against other home computers primarily used to play video games and enjoyed a strong supply of game software. The comparatively low price for a complete computer system with dedicated monitor, its high resolution monochrome text and graphic capabilities and the possibility to run CP/M software also rendered the system attractive for business users, which was reflected by a wide selection of application software.

During its lifetime, the CPC series sold approximately three million units.

source: wikipedia

I have received this motherboard of a CBM 8032 to repair from Rossano T.

The motherboard was devastated by rust, many components are short-circuited due to rust that was abundant on the pins side of the chip. Unfortunately the computer was turned on to test it, causing the total breakdown of more components.

I have installed 40 socket because some components are rusty other are dead, however some traces under the chips are eaten by rust and and i had to rebuild.

The repair and cleaning took me a very long time and a lot of patience, it took me about 10+ hours.

Components Replaced:

• 1 x 4650 (6845P) CRT Controller
• 3 x 4116 RAM
• 2 x 2114 Video RAM
• 5 x 74LS244
• 3 x 74LS74
• 1 x 74LS02
• 1 x 1uf 100v Capacitor

Phases of the repair:

12►

Some new games (Cracked / Trained or Unrealeased) for Commodore 64 have been released from your favorites groups:  Alf Yngve, The New Dimension, Bad Taste, Really Proud Lamers, Antarctica, The Hidden Farts, Genesis Project, Laxity and TRIAD.

Download:

• Bank Run (946)
• gPng v1 (957)
• Ann Gong +3HD (993)
• Hit the Brick +1ED (966)
• Axiens HS (995)
• MArkanoid +4HD 101% (1015)
• Dot Gobbler +1D (986)
• Trance Sector CE +8HD [pal/ntsc] (970)
• Radar Simulation +D (1128)
• Guns \'n\' Ghosts +9MD 101% (1129)
• All Games in One Archive (2540)

source: csdb.dk

123►

This gallery shows some stages of cleaning the computer Apple IIe and the Apple Monitor ///.

I have also made minor repairs which i describe below:

• Fixing the keyboard connector on keyboard side (some keys not working)
• Adjusting the yoke of the CRT tube (the screen is lightly rotated)
• Replaced the LED of power-on (CR1) of the Apple IIe (LED was off)
• Removing the RIFA filter capacitor (the capacitor was exploded)

Autopsy:

from Wikipedia:

The Apple Monitor /// was a green phosphor CRT-based monochrome monitor manufactured by Apple Computer for the Apple III personal computer, introduced in 1980.

As Apple’s first monitor in their business line of machines, it preceded the Apple Monitor II by several years. The Apple Monitor ///’s main feature was the coating on the CRT to reduce glare. The Apple Monitor /// was also compatible with the Apple II+, Apple IIe, Apple IIc, and even the later models: the Apple IIc+, and the Apple IIgs through its composite video output jack.

source: wikipedia

Autopsy:

12►

from Wikipedia:

The Disk II Floppy Disk Subsystem, often spelled as Disk ][, was a 5¼-inch floppy disk drive designed by Steve Wozniak and manufactured by Apple Computer. It was first introduced in 1978 at a retail price of US$495 for pre-order; it was later sold for $595 including the controller card (which can control up to two drives) and cable. The Disk II was designed specifically for use with the Apple II personal computer family to replace the slower cassette tape storage and cannot be used with any Macintosh computer without an Apple IIe Card as doing so will damage the drive and/or controller.

Apple produced at least six variants of the basic 5¼-inch Disk II concept over the course of the Apple II series’ lifetime: The Disk II, the Disk III, the DuoDisk, the Disk IIc, the UniDisk 5.25″ and the Apple 5.25 Drive. While all of these drives look different and they use four different connector types, they’re all electronically extremely similar, can all use the same low-level disk format, and are all interchangeable with the use of simple adapters, consisting of no more than two plugs and some wires between them. Most DuoDisk drives, the Disk IIc, the UniDisk 5.25″ and the AppleDisk 5.25″ even use the same 19-pin D-Sub connector, so they are directly interchangeable. The only 5.25″ drive Apple sold aside from the Disk II family was a 360k MFM unit made to allow Mac IIs and SEs to read PC floppy disks.

This is not the case with Apple’s 3.5″ drives, which use several different disk formats and several different interfaces, electronically quite dissimilar even in models using the same connector, and are not generally interchangeable.

source: wikipedia

Autopsy:

12345►

from Wikipedia:

The Apple IIe (styled as Apple //e) is the third model in the Apple II series of personal computers produced by Apple Computer. The e in the name stands for enhanced, referring to the fact that several popular features were now built-in that were only available as upgrades and add-ons in earlier models. It also improved upon expandability and added a few new features, which, all combined, made it very attractive to first-time computer shoppers as a general-purpose machine. The Apple IIe has the distinction of being the longest-lived computer in Apple’s history, having been manufactured and sold for nearly 11 years with relatively few changes.

Apple had planned to retire the Apple II series after the introduction of the Apple III in 1980; after that machine turned out to be a disastrous failure, management decided the further continuation of the Apple II was in the company’s best interest. So after three and a half years at a stand-still, came the introduction of a new Apple II model — the Apple IIe (codenamed “Diana” and “Super II”). The Apple IIe was released in January 1983, the successor to the Apple II Plus. Some of the hardware and software features of the Apple III were borrowed in the design of the Apple IIe. The culmination of these changes led to increased sales and greater market share of both home and small business use.

One of the most notable improvements of the Apple IIe is the addition of a full ASCII character set and keyboard. The most important addition is the ability to input and display lower-case letters. Other keyboard improvements include four-way cursor control and standard editing keys (Delete and Tab), two special Apple modifier keys (Open and Solid Apple), and a safe off-to-side relocation of the “Reset” key. The auto-repeat function (any key held down to repeat same character continuously) is now automatic, no longer requiring the “REPT” key (now gone) found on the previous model’s keyboard.

source: wikipedia

SID Duzz it, it’s a SID Music Editor by Geir Tjelta of SHAPE.

Download: SID Duzz It v2.1.6 (963)

source: csdb.dk

Autopsy:

12►

Donated By: Andrea Pierdomenico

from The Personal Computer Museum:

The PowerPad is Chalkboard’s graphics tablet. With its combination of features, reasonable price, friendly support, and wide range of software, it would be an excellent addition to your hardware.

The first thing you notice about the PowerPad is that it’s big: it measures 17 inches by 14 inches, with a drawing surface 12 inches square. It is easier to draw on than the smaller surfaces of other tablets.

The PowerPad uses 14,400 tiny digital switches to read where pressure is applied to the pad. There are 10 x 10 per inch. Unlike the surfaces of other pads, the PowerPad has no problem resolving simultaneous multiple inputs. This ability allows the PowerPad to be used as much more than just a graphics tablet: it becomes a flexible input device.

If you’ve done a little arithmetic, you may be wondering about the PowerPad’s resolution. Ten switches per inch by 12 inches equals 120 points, or pixels – not even as high resolutions as Graphics 7! However, it’s possible to design a program using the Atari’s highest-resolution screen, by “software stretching” of the resolution.

The version of Micro Illustrator ($49.45) for the PowerPad has a special feature called “Scale” that uses ,Software stretching” to let you draw pixel by pixel, even though the tablet’s resolution isn’t as high as Micro Illustrator’s.

Hardware isn’t of much use without software, but the PowerPad doesn’t come with any. However, Chalkboard offers several programs in cartridges requiring 32K of RAM for the Commodore VIC-20.

source: pcmuseum.ca

Regenerator is an interactive disassembler for C64 binaries. Regenerator will load any standard C64 .PRG file (or VICE snapshot) and disassemble it for your convenience.

There are a few options you can choose to change the output and a few tools to make the output look better and more useful to programmers. Regenerator runs under M$ windows and need .net 3.5 (or 4.0) runtime.

New in version 1.3:

• Added REMOVE command to remove part of the data from dissasembly.
• Added EDIT BLOCKS window to Edit all the DATA, TEXT and REMOVED blocks manually.
• Added COPY to Clipboard functionality (insert key) with FULL or CODE only modes.
• Added possibility to add user-defined COMMENTS to the code. This can be done as a FULL line comment or as a SIDE comment!
• Added USER LABELS – you can now add a label to any address and it will be used in the disasembly. If there should be an automatic label generated for it then it will be overriden. Also added USER LABELS editor which is part of the old Label Prefixes window. You can add/edit and remove user labels within this screen and have a general overview of the user labels.
• Added high and low partial references to immediate opcodes. This means that code like LDX #$A0 STX smwhr LDX #$BB STX smwhr+1 will be disasembled as LDX #<pBBA0 STX smwhr LDX #>address STX smwhr+1. This includes loads and stores in different order and with different registers. There is also a context menu command that lets you disable this on a currently selected address (if auto creation fails). NOTE: excluded address in STA opcodes will not be generated like this!
• Fixed the Add BLANK LINE and Remove BLANK LINE so it actually works as it should.

Download: Regenerator disassembler v1.3 (946)

source: csdb.dk